is and irc specification for crushing value

Aggregate Crushing Value Apparatus Make: LabTek Model: SL-AG-001 Origin: India Standards: IS 2376 (PART-IV) & BS 812:111 Specification: The Aggregate Crushing Value (ACV) test set provides a relative measure of the resistance of an aggregate to crushing under a …

Get Price

Request A Qote

If you have any problems or questions about our products or need our support and assistance, please contact us and you will be replied within 24 hours. We promise we will never reveal your information to the third party. Thank you!

Our Solutions

  • Aggregate Crushing Value Test Vidyarthiplus

    Aggregate Crushing Value Test Vidyarthiplus

    Aggregate Crushing Value Test ... However aggregate crushing values have not been specified by the IRC for coarse aggregates to be used in bituminous pavement construction methods. 1. Methods for Sap:tpling and Testing of Mineral Aggregates, Sands and Fillers BS 812,British Standards ... Standard Specification and Code of Practice for ...

    read more
  • IS 2386 4 1963 Methods of test for aggregates for

    IS 2386 4 1963 Methods of test for aggregates for

    aggregate crushing value of coarse aggregate. NOTE 1 -The ‘aggregate crushing value’ gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre- gate of ‘aggregate crushing value’ 30 …

    read more
  • State Responder 1. Does your state allow crushed Any

    State Responder 1. Does your state allow crushed Any

    No No R-value is determined. A required gradation is usually specified. See link below in #4 for the general “Crushed Stone Subgrade” specification gradation required. Depending on the situation, the gradation shown in the general specification could be modified. Attached (1st attachment) is an example of a “modified” project special

    read more
  • Full page fax print Public.Resource.Org

    Full page fax print Public.Resource.Org

    IRC:27-2009 SPECIFICATIONS FOR BITUMINOUS MACADAM (FIRST REVISION) Published by ... from crushing operation. (VGY Viscosity VG. tY for . IRC:27-2009 Property ... Test Grain size analysis Flakiness & Elongation Index (combined) Los Angeles Abrasion Value Aggregate Impact Value Soundness (Sodium or Magnesium), Sodium Sulphate Magnesium Sulphate ...

    read more
  • Los Angeles Abrasion Test on Aggregates Values for

    Los Angeles Abrasion Test on Aggregates Values for

    Los Angeles test is commonly used to evaluate the hardness of aggregates. The test has more acceptability because the resistance to abrasion and impact is determined simultaneously. Depending upon the value, the suitability of aggregates for different road constructions can be judged as per IRC specifications as given:

    read more
  • Lumber Design Values WWPA

    Lumber Design Values WWPA

    Lumber Design Values. Design values provided herein are for Western softwood species manufactured and shipped by mills in the 12 contiguous Western states and Alaska. Except as otherwise noted, the values are computed in accordance with ASTM standards based on clear-wood tests or on tests of full-size pieces in specific grades.

    read more
  • Abrasion Test Test to Determine the Abrasion Value

    Abrasion Test Test to Determine the Abrasion Value

    Measurement of toughness and resistance like degradation, crushing, and disintegration is the right definition of the Abrasion test. ... IS Recommended Los Angeles abrasion test Values ... On the basis of this value, the suitability of aggregates for different road constructions can be judged as per IRC specifications as given.

    read more
  • Abrasion Test On Aggregate Los Angeles Abrasion Test

    Abrasion Test On Aggregate Los Angeles Abrasion Test

    Los Angeles Abrasion Value of Aggregate = 58. IS Recommended Los Angeles Abrasion Value of Aggregate for Pavements. A Los Angeles test is performed to find the hardness of aggregates. On the basis of this value, the suitability of aggregates for different road constructions can be judged as per IRC specifications as given,

    read more
  • Crushing Value of Aggregate vlab.co.in

    Crushing Value of Aggregate vlab.co.in

    The crushing value of aggregates is rather insensitive to variation in strength of weaker aggregates. For this reason, a simple test known as 10 percent fine value is introduced. When the aggregates crushing value become 30% or higher, the results are likely to be inaccurate. Aggregate Crushing Load (Source: IS 2386(Part 4):1963) The aggregates ...

    read more
  • Specification for Bituminous Macadam

    Specification for Bituminous Macadam

    2.1 This specification deals with the basic outline for the design, construction and controls needed while laying bituminous macadam course for highways. 2.2 Bituminous macadam (BM) shall consist of mineral aggregate and appropriate binder, mixed in a hot mix plant and laid with a mechanized paver. It is an

    read more
  • IS 383 1970 Specification for Coarse and Fine

    IS 383 1970 Specification for Coarse and Fine

    2.1.2 Crushed Stone Sand - Fine aggregate produced by crushing hard stone. 2.1.3 Crushed Grace1 Sand - line aggregate produced by crushing natural gravel. . 2.2 Coarse Aggregate -- Aggregate most of which is retained on 4*75-mm IS Sieve and containing only so much finer material as is permitted for

    read more
  • IS 9376 1979 Specification for apparatus for measuring

    IS 9376 1979 Specification for apparatus for measuring

    IS:9376-1979 1. SCOPE 1.1 This standard covers requirements of the apparatus for measuring aggregate crushing value and ten percent fines value. 1.1.1 Two sizes of apparatus are covered in this standard, one with 150 mm cylindrical cell and the other with 75 mm cylindrical cell. 2.

    read more
  • Aggregate Crushing Value Test Determine Aggregate

    Aggregate Crushing Value Test Determine Aggregate

    Aggregate crushing value test on coarse aggregates gives a relative measure of the resistance of an aggregate crushing under gradually applied compressive load. Coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected to a specified load under standardized conditions.

    read more
  • IS 2720 8 1983 Methods of test for soils Part 8

    IS 2720 8 1983 Methods of test for soils Part 8

    to crushing ~during compaction. 0.3 For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, *Methods of test for soils : Part 7 Determination of water content .-dry densit\ relation using light compaction ( secondrecision ). 3

    read more
  • Aggregate Crushing Value Civil Engineering Portal

    Aggregate Crushing Value Civil Engineering Portal

    Procedure to determine Aggregate Crushing Value i) The aggregates passing through 12.5mm and retained on 10mm IS Sieve are oven-dried at a temperature of 100 to 110 o C for 3 to 4hrs. ii) The cylinder of the apparatus is filled in 3 layers, each layer tamped with 25 strokes of a tamping rod.

    read more
Click avatar to contact us
Click avatar to contact us
gotop